Neglected Pre-Ride Motorcycle Maintenance Part 2

TAKING AIM, by Chris Maida, Editor

TAKING AIM by Chris Maida, Editor

TAKING AIM by Chris Maida, Editor

In the last issue, I wrote about how many owners routinely neglect their bike’s tires. This time around, we’ll look at the second important area I see many owners overlooking: their brake systems. Checking the brake pads, brake lines, and rotors takes only a few minutes, since they’re out in the open. Thankfully, these components only need to be checked every 2,500 miles. However, if you ride less than 1,000 miles a year, don’t go by the bike’s mileage in regard to the brake lines, since time is the enemy here as much as mileage. Every six months should be sufficient.

To check the brake pads, look at where both pads contact the rotor. If the metal baseplate of the pad is close (under 1/16″) to touching the rotor, change the pads. Inspect the rubber section of the brake lines for cracks, the metal areas for rust. Needless to say, you don’t want to see either one. If you do, replace the lines. For the rotors, look for bluing or grooves on either side of the rotor. Slight grooves in the rotor are normal, deep grooves are not. Also make sure the bolts are tight. You don’t have to pull out a torque wrench to check the hardware, just put a tool on them and see if they move easily. If they don’t, they’re good to go.

The last brake maintenance item is a bit more involved: changing the brake fluid. This is the area I see neglected the most. Thankfully, you only swap out the brake fluid every two years if your bike uses DOT 3 or 4. That’s how long it takes DOT 3 or 4 to absorb enough moisture to become a problem. Water inside the brake system corrodes the brake lines and such from the inside and can cause a failure even though things look fine on the outside. Just for the record, you can put DOT 4 in a DOT 3 system, but don’t put DOT 3 in a DOT 4 system. Also, DOT 5 and DOT 5.1 are not the same. Don’t interchange them!

Of course, while you’re looking at the brake system, which also includes checking the brake fluid level, you can also check the axle nuts, wheels, etc., but a long checklist is, I think, the main reason most riders don’t check anything. Personally, I recommend inspecting a few different items each time you’re about to fire off the engine. This trip it’s the brake system, next time it’s the wheels and axle nuts, etc. Sure, the best way is to check everything every time you plan on going for a ride, but that’s not going to happen in most cases. If it’s all or nothing, it’s safer, in my opinion, to check a section of your bike each time you plan on going for a ride. That said, you should always check the tires before each ride!

See you on the road.

Chris Maida

Follow me on Facebook

 

To order back issues, visit Greaserag.com.

To subscribe to the PRINT edition, click here.

To receive DIGITAL DELIVERY, click here.

New from Drag Specialties in October

DRAG SPECIALTIES® HOTOP DESIGNS FOOTPEGS AND SHIFT PEG

Drag Specialties, an industry leader in stylish, high-quality aftermarket parts and accessories for Harley-Davidson® motorcycles, is proud to announce new footpegs and shift peg styles only available from Drag Specialties.

These new pegs feature high-quality, die-cast construction, black finish and knurled nylon insets for style and durability for all-day riding. Male-mount ootpegs are sold in pairs for just $59.95 and shift peg is sold each for only $24.95.

For all Drag Specialties footpegs and shift pegs, and for the widest selection of premium parts and accessories for Harley-Davidson motorcycles.

DRAG SPECIALTIES® REAR PULLEYS

Drag Specialties’ new rear pulleys for 09-11 FLHT/FLTR/FLHR/FLHX are the perfect combination of style and performance. Manufactured in the U.S.A. exclusively for Drag Specialties, these chromed billet pulleys come in 68-tooth configuration and are available in Mesh or Klassic styles.

Both styles feature a clean, sleek look that matches Drag Specialties brake rotors. They are also the perfect complement to Drag Specialties laced wheel.

With a suggested retail of just $439.95, these rear pulleys are an inexpensive way to add a lot of style to late-model Harley-Davidson® touring models. Be sure and see the full line of Drag Specialties pulleys, rotors and wheels, along with the widest selection of premium parts and accessories for Harley-Davidson motorcycles.

DRAG SPECIALTIES® POLISHED STAINLESS STEEL BRAKE ROTORS

As an industry-leading dealer-distributor of aftermarket parts and accessories for Harley-Davidson® motorcycles, Drag Specialties only puts its name on the best of the best. So when they put their name on brake rotors, you know they’ve got to be good.

Available for most 00-011 Harley-Davidson models, Drag Specialties’ high-quality front and rear rotors are constructed of 430 stainless steel and polished to a mirror-like finish. Made in the U.S.A., they come in 11.5″ or 11.8″ diameter size in Klassic or Mesh style for just $99.95 suggested retail.

Be sure and see the full line of Drag Specialties rotors and brake products, along with the widest selection of premium parts and accessories for Harley-Davidson motorcycles.

DRAG SPECIALTIES® SADDLEBAG RAIL SUPPORT BRACKETS

For 30 years Drag Specialties has been synonymous with stylish, high-quality aftermarket parts and accessories for Harley-Davidson® motorcycles. A case in point is Drag Specialties’ new saddlebag rail support brackets for 80-08 FLT, FLHT, FLHR, FLHX, FLTR models.

Constructed to last, these new support brackets feature heavy-duty steel construction that is 15% thicker than stock plates to prevent breakage. Sold each, and with a chrome finish for added style, they mount in a snap using existing hardware.

They are available for left or right side (replacing OEM #90718-79C and 90720-79C) and have a suggested retail of just $49.95. For the entire line of Drag Specialties saddlebag-related products, along with the widest selection of premium parts and accessories for Harley-Davidson.

Visit at :www.dragspecialties.com